Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain and are durable and long-lasting. In contrast to aluminium and timber, they are not susceptible to get rusty or decay.

It is important to clean and oil UPVC windows and doors on a regular basis. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. You should take the time to make sure that your windows are in good shape.

For single pane windows, it is relatively easy to replace them, and the new window is usually able to fit into the frame of the previous one easily. However If you have double glazing near me-pane windows that are held in place by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this instance, you will need to find some plastic spacers to help the new pane to fit correctly into the frame of the window.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes, so that any shards fall on the fabric, not onto the floor which could cause them to be trampled under.

It's a great idea to seal the gap after the glass has been removed. This will keep water and drafts from entering your home until a professional is able to fix the window. It also acts as a barrier, preventing any intruders from gaining entry into your home. If the gap between the door and the window is large, you might want to use security screens that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows with sash. However, over time, they are susceptible to a range of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. It is crucial to act immediately if you notice your uPVC windows are falling down.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows so you can reach the frame. Then, remove both the top and bottom hinges using a screwdriver and adjust them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and test it for fitting. If you're happy with the fit, Window repair you can tighten the screws to ensure they remain in position.

If you can't reposition the hinges you may require replacing the seal. Over time, rubber seals lose their elasticity and become dry which causes their tightness to decrease. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also loosen up. The majority of the time this is due to screws that have come loose over time. However, it could occur because the handle mechanism has worn out. It's fairly simple to repair a loose uPVC handle. First, you'll need to close the window and then perform a test fitting. The joint at the corners of the sash should align with the joint on the casing. If it isn't, Window Repair you can use the screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, it's crucial to take action. The leaks of water through windows could cause structural damage to your home and impact your ability to regulate the temperature in your home. The most common cause for leaks in uPVC windows is that the sealant around the frame has been damaged or not present.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on how severe the issue is, the old caulking may have to be removed. It is crucial to keep in mind that when it comes to uPVC window repairs, do not be tempted to 'over-caulk' as this will only make the area harder to clean and can reduce your energy efficiency.

Make sure that the drainage holes are free of debris in them and that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you might need to consider replacing the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leak is coming from between the glass of your double-glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sliding. Again this can easily be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open with ease It could be hinges at fault. They can be replaced by any competent DIYer and can usually be done within a few minutes.

Like all mechanical parts, hinges can be damaged over time. It is essentially a simple process but it can be simpler when you have a person to help hold the frame up.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The issue could be caused due to opening the window in the wrong way or by a poor installation at the factory. Sending us photos through our website can often resolve the problem. We are happy to provide suggestions.

It is also crucial to ensure that the hinges are lubricated regularly. Applying an engineering lubricant that is light to the hinges is an ideal method of doing this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. Ideally, you should do this once a year. WD40 or other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. The hinges can also be disaligned as a result of wear, which can cause a gap where the sash and frame meet. These can be easily repaired by giving them a good cleaning, but in the event that they are beyond repair it might be necessary to have them realigned or replaced. The interlock, which is located on the hinge of the window repair and can also become misaligned, again it is possible to just give them a clean but in some cases it might be necessary to have these replaced.

The second most frequent reason for draughts are the window seals. These can become worn down or damaged over time and let air escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures and lessen the risk of draughts.

One of the most effective ways to reduce draughts is by using an draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be put on the top of your windowsill. They can help block out cold air and keep your home warm and cozy!

Your upvc windows can keep providing excellent insulation and security to your home with regular maintenance and repairs. However, it is important to recognize that all windows have a life span and eventually, they will reach a point where it is more efficient to replace them than fix them. If you are experiencing issues with your Upvc window, it's best to consult an expert immediately.